1973 Porsche 911 CDI Box 3 pin, Retrofit of Your Original

Product Description:

Retrofit of YOUR Bosch 3 Pin CDI Box
We'll retrofit your Bosch CDI with our modern electronics.
Please note we can't retrofit aftermarket boxes.
Excludes exterior cleaning, see "exchange" listing if that's needed.
For Porsche 911 models ‘69-‘77 and 914/6.
Includes free download of CDI System TSB.

Send in your old Bosch CDI box, and we'll replace the internals with our advanced digital CDI electronics package. With a retrofit we don't clean the outside of your case, but we do include a new Vorsicht decal. If you'd like a cleaned outer case, please see our "Exchange" listing.

Each CDI box we rebuild is fully tested on our proprietary testing equipment before it leaves our facility. There are however a number of installation factors, vehicle conditions, and practices that can make a CDI box appear non-functional, or that can actually damage the unit during or after installation. For this reason, we recommend that any CDI box be installed by a qualified Porsche mechanic who is truly competent with Porsche CDI ignition systems. We stand behind our CDI boxes with a 2-year warranty on defects in materials and assembly. 

With the Porsche models that use CDI systems now up to 50+ years old, there are many issues that negatively impact CDI box operation, including aftermarket parts that don’t conform to factory standards, discontinuation of original Bosch ignition parts, poor wiring and installation, and general wear and tear on the electrical system. These and other factors affect how well the system operates, and they contribute to ignition system failures. Moreover, the original Bosch units lose power as RPMs increase, and the circuitry is relatively unprotected from issues seen on these cars today.

Advantages of using the Partsklassik CDI:

• “A” Terminal Disconnect protection
• Protected Trigger Signal Input Filter
• Input Voltage Correction
• End User Settable RPM Limiter
• Misfire Over Voltage Protection
• True 450 Volt Primary CDI
• High Efficient Design Resulting in Less Heat Generation
• Low System Current Draw
• Won’t Lose Power as RPM Increases
• Plug compatible with all factory Porsche Models
• No Phase Modification on Trigger/Firing Point
• 2 Year Warranty Against Defects in Materials and Assembly

Please note that while Partsklassik CDI boxes have built-in protections from external issues, these protections are not infinite. It is still important to maintain and service your electrical and ignition systems properly. This includes the often overlooked specs on secondary resistance values (i.e., on plug wire connectors, rotor, cap-to-coil wire).

For more info on CDI systems, see our white paper HERE

Manufacturer Information:

Partsklassik
Partsklassik was founded by a Porsche®-trained mechanic with decades of repair and restoration experience. We are a parts and components restorer, as well as a manufacturer of previously unavailable parts for vintage and classic Porsche® vehicles. 

We also carry thousands of OEM and aftermarket parts spanning all systems of the air cooled Porsche® models, including the 356, 911, 912, 914, and 930. We continuously add new products and services to meet the needs of the vintage Porsche® enthusiast. 

Reviews and Ratings:

1 Customer Review(s)

5 Star

1  (100%)

4 Star

0  (0%)

3 Star

0  (0%)

2 Star

0  (0%)

1 Star

0  (0%)

Please login first to write a review.

Overall

Value

Performance

Works well , very satisfied .

Reviewed by Richard  H

11/30/2018 6:40:57 PM

• 1969 Porsche 911
• 1970 Porsche 911
• 1972 Porsche 911
• 1973 Porsche 911
• 1974 Porsche 911
• 1975 Porsche 911
• 1976 Porsche 911
• 1977 Porsche 911
• 1970 Porsche 914/6
• 1971 Porsche 914/6
• 1972 Porsche 914/6
• 1973 Porsche 914/6
• 1974 Porsche 914/6
• 1975 Porsche 914/6
• 1976 Porsche 914/6

All returns require pre-approval. All returns are subject to a 25% restocking fee, with the exception of approved warranty returns, or if we ship a different part number than ordered. We do not accept returns after 30 days.

Inspect your order immediately when it arrives. We must be notified within 5 days if there are any missing, damaged, or incorrect parts.

Returns (except warranty) won't be accepted if the part:
 - Has been installed, used, damaged, is dirty or incomplete
 - Is not sellable as new
 - Arrived in sealed packaging that has been opened
 - Is an electrical part, a distributor spring, a custom or cut-to-length item, or a Special Order
 - Was purchased more than 30 days earlier

Parts must be returned properly padded in a sturdy cardboard box. Returns sent in envelopes will be refused. Items damaged in transit to us cannot be refunded. All returns must be shipped prepaid.